Pt d5500u manual

TQBJ Page 2: Important Safety Notice This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP based projector. Page 4: Table Of Contents Using the remote control unit Do not insert any foreign objects into the projector.

Ask an Authorized Service Center to clean inside the projector at least once a year. Page 8: Precautions On Handling Avoid installing the product in a place exposed to vibrations or impacts. If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or Page 10 Moves the mouse cursor. Numeric buttons In a system that uses a multiple number of projectors, these buttons serve to specify a particular projector. They are also used to enter the password when the password for service personnel needs to be entered.

Level-adjusting feet page 22 Use these feet to adjust the tilt of the projector. The leveling feet at the front left and right can be adjusted.

Remote control receiver window rear page 14 This also receives the signal beam coming from the remote control. Page Side-Mounted Connection Terminals pin female. Page Using The Remote Control Unit The remote control should normally be aimed at either the front or rear remote control receiver window on the projector figure 1. Page Setting Projector Id Number To Remote Control Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control.

It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

If this is the case, connect a TBC between the projector and the video deck. Remove the lens. Dust or dirt may cause defective contact. The power indicator lights up red, and the projector is placed in the standby mode. Please turn the power on again after a while. Press the LENS button on the remote control or on the control panel of the main unit.

Page Automatic Adjustment Auto Setup Still image Using the SHUTTER function If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily. Page On-Screen Menus On-screen menus Structure of menu screens Menus are extensively used for configuring, adjusting or reconfiguring the projector.

Large Venue Classroom Interactive Conference. Find a Projector. Classroom Interactive Portable. Throw Calculator. Jump to Highlights Calculate Throw Distance. Product Downloads Product Sheet. Pull them horizontally out. Loosen the 1 screw fixing the lamp unit cover until it idles, slightly slide the cover horizontally and remove it. Page Removal Of J-P. Board block. Pull out the flexible cable connected to the J-P.

The reverse side of A-P. Board Unscrew the 10 screws and remove the A-P. The block of the terminal metal fittings, J-P. Board and D-P. Board remains. Board block according to the steps 1 through 3 in the section Unscrew the 2 screws and release the 2 grounding terminals. Unscrew the 6 screws and remove the shield cover. Removal of Ballast-1 and Ballast-2 Modules Remove the upper case according to the section Unscrew the 3 screws and release the grounding terminals.

Unscrew the 2 screws and release the lamp unit terminals. Loosen the 2 screws until they idle and open the exhaust fan unit Loosen the 2 screws fixing the lamp unit until they idle and remove the lamp unit 2. Unscrew the 3 screws and release the ballast block. Unscrew the 2 screws and remove the ballast fan. Removal of Lamp Unit Loosen the 1 screw fixing the lamp unit cover until it idles, slightly slide the cover horizontally and remove it. Removal of Projection Lens Fully turn the projection Lens counterclockwise.

Turn the projection lens counterclockwise in addition while pressing the lens lock button. Unscrew the 1 screw and release the lamp unit terminal 2.

Unscrew the 1 screw and remove the thermofuse. Unscrew the 1 screw and remove the shield cover. Unscrew the 2 screws and release the grounding terminals.

If it becomes dirty or damaged, the performance may be deteriorated. Removal of Full Reflection Mirror complete Remove the upper case according to the section Unscrew the 2 screws and remove the color wheel cover.

Unscrew the 3 screws and remove the full reflection mirror complete.